13 ft disc for my DA9190 and MF1155
 

Hi together!

To have some equipment for the tillage I started with a 13ft disc today. Here are the first parts....nearly 2" diameter concaved steel discs...
They will be assembled with some tubes and a threaded rod.
http://www.bilder-hochladen.net/file...0h-is-2f37.jpg

regards
Frank

Re: 13 ft disc for my DA9190 and MF1155
 

...I do not build a certain type of disc, but I hope it will look a bit like this when it´s finished...:
http://www.flaman.com/agriculture/im...hek2Offset.jpg

Re: 13 ft disc for my DA9190 and MF1155
 

That is a nice Disc Frank there is a guy here in the US that goes to the toy shows that has built that very same one to a T very nice unit. Cant wait to see more by the way were did you get the concave disc's made.

Re: 13 ft disc for my DA9190 and MF1155
 

I am also interested in where the discs came from or where/how they were made. I want to make a disc for my JD

Re: 13 ft disc for my DA9190 and MF1155
 

If you need and are interested, I found this on Ebay:

http://www.ebay.com/itm/JOHN-DEERE-D...item4d02483471

-RCT

Re: 13 ft disc for my DA9190 and MF1155
 

I got the discs from the local hardware store. Ususlly they are used as end caps for welded tubes.

Re: 13 ft disc for my DA9190 and MF1155
 

The discs are connected to one shaft...:
http://www.bilder-hochladen.net/file...0h-iu-6826.jpg
http://www.bilder-hochladen.net/file...0h-iv-3a06.jpg
Next part will be the frame...

Re: 13 ft disc for my DA9190 and MF1155
 

That is looking great. Will it be all brass?

Re: 13 ft disc for my DA9190 and MF1155
 

I think so....some parts brass, maybe some Aluminum...

Re: 13 ft disc for my DA9190 and MF1155
 

Looking great!!

Re: 13 ft disc for my DA9190 and MF1155
 

Some more steps forward...:
http://www.bilder-hochladen.net/file...0h-iy-2291.jpg

http://www.bilder-hochladen.net/file...0h-j0-8411.jpg

http://www.bilder-hochladen.net/file...0h-j1-fae0.jpg

With the crank I can adjust the level of the hitch...


Regards
Frank

Re: 13 ft disc for my DA9190 and MF1155
 

Look's great, Frank.

Cheer's, Neil.

Re: 13 ft disc for my DA9190 and MF1155
 

A few days ago the parts fom CTI arrived...
The spindle cylinder for lifting the disc is now mounted.
http://www.bilder-hochladen.net/file...0h-j7-2dea.jpg

Re: 13 ft disc for my DA9190 and MF1155
 

Today I made the first test run of the lifting system...it works great with te cylinder!
http://www.bilder-hochladen.net/file...0h-jf-fccb.jpg

To adjust the tilling depth I put the tractor 15 millimeter higher. In this position I can adjust the parallelism of the discs to the ground by turning the spindele...
http://www.bilder-hochladen.net/file...0h-jg-1595.jpg

If I find the time and the weather is ok I will make a video of the testrun outdoors in the next few days.

Re: 13 ft disc for my DA9190 and MF1155
 

Looks fantastic!!! Did an awesome job on it! Cant wait to see the video!

Re: 13 ft disc for my DA9190 and MF1155
 

great work ....

that cylinder is nice - better looking than the Firgelli styles....

Re: 13 ft disc for my DA9190 and MF1155
 

First test run in (very) hard ground... :D
http://www.myvideo.de/watch/8694116/...is_9190_Test_1

Re: 13 ft disc for my DA9190 and MF1155
 

Cool video! Looks pretty good

Re: 13 ft disc for my DA9190 and MF1155
 

Very nice work, Frank. The disk looks awesome. That hard packed ground isn't a good judge for the disk's functionality though. I'm sure it would work a lot better in a more scale, packed dirt field.

Re: 13 ft disc for my DA9190 and MF1155
 

Video look good. I like the new tire setup. It looks like you need to adjust the hitch to have more rear dig. It looked like the rear was in the air and allowing the front to pull sideways and not cut like it should.

Re: 13 ft disc for my DA9190 and MF1155
 

That´s exactly what ist does. the tilling depth is still adjusted to 15 millimeters and if the front does not get in the ground so deep, the rear stays in the air. It also lifts the rear axle up, but the DEUTZ-ALLIS has 4wd, so the tractor still pulls over the frontwheels. In the next video it will be better... :o

Re: 13 ft disc for my DA9190 and MF1155
 

Awesome - I like it - don't get discouraged by the workings of the plow - hard pack is hardly a good test. I would rather think that fine potting soil would be a better material?

Re: 13 ft disc for my DA9190 and MF1155
 

Another test...
http://www.myvideo.de/watch/8701031/...Z_ALLIS_Test_2
Some things are to do:
- The spindle for the adjustment of the tilling depth needs some more clearance
- maybe I´ll sharpen the discs a little bit, now they are 2 millimeters thick
- maybe I´ll put some weight on it...

With more clearance the disc runs smoother over humps. The clearance in the spindle makes the drawbar more flexible when it´s connected to the tractor.
After that it will be ready for the paintjob I think...

Re: 13 ft disc for my DA9190 and MF1155
 

Looks like it was running better. I still love your tractor.

Re: 13 ft disc for my DA9190 and MF1155
 

Some more details:
http://www.bilder-hochladen.net/file...0h-ji-2468.jpg
A toolbox for the electric components and some more weight...:
http://www.bilder-hochladen.net/file...0h-jk-3328.jpg

Re: 13 ft disc for my DA9190 and MF1155
 

Good idea for adjustable weight! That should help push it further in the dirt

Re: 13 ft disc for my DA9190 and MF1155
 

Sweet work!

Re: 13 ft disc for my DA9190 and MF1155
 

After several time some progress: The zgly white bix is gone...the speed controller for the spindle cylinder is fixed below the copper cover between the frasmerails...

http://www.bilder-hochladen.net/file...0h-op-3557.jpg