RC Truck and Construction

RC Truck and Construction (https://www.rctruckandconstruction.com/index.php)
-   General Discussion (https://www.rctruckandconstruction.com/forumdisplay.php?f=12)
-   -   Does anyone make a Folding Gooseneck? (https://www.rctruckandconstruction.com/showthread.php?t=6852)

Straywolf 05-01-2013 07:37 AM

Does anyone make a Folding Gooseneck?
 
I was just wondering if anyone made a Folding Gooseneck trailer like Load King?

Something like this, here is the link

http://www.loadkingtrailers.com/folding_goosenecks.aspx

tc1cat 05-01-2013 07:55 AM

Re: Does anyone make a Folding Gooseneck?
 
I don't think so but it would be an interesting trailer to make and have it operate from a radio.

Dieselchopper 05-01-2013 08:03 AM

Re: Does anyone make a Folding Gooseneck?
 
It is a trailer I plan to make in time once I have the winch truck done. I will be building from scratch.

Rvjimd 05-01-2013 08:16 AM

Re: Does anyone make a Folding Gooseneck?
 
That would be a neat trailer in RC! I have operated one just like it years ago. The geometry would be tough in a small scale:o. There are hyd jacks with small pads under each corner at the end of the main bed, and then the folding section.

We used to load the bigger stuff first and then put something lighter, like a skid steer on the neck. It was power by a small kholer and didn't seem to have any trouble lifting, but it was not fast...

Jim

Espeefan 05-01-2013 11:30 AM

Re: Does anyone make a Folding Gooseneck?
 
I like that! The other trailer I have been looking at is this one -

http://www.traileze.com/TE701-TE801.html

Either would be a cool model.

WhiteWolf McBride 05-01-2013 12:01 PM

Re: Does anyone make a Folding Gooseneck?
 
Agreed on the Slider...

Seen 'em in operation, and they'd be rather easily done, just make a screw-drive to push-pull the axle-assembly forward/aft, and then rails for the assembly to slide on.

The folder, that would seem to be more complicated, as you'd need the right angles on the neck to get it to bend right, and then there are the power-disconnect issues... but you have those for almost all the trailer lighting assemblies (no-one's made a 5th wheel-mounted power transfer system...)

Would love to see one of the these made: A Murray Robo-Link http://www.youtube.com/watch?v=8u_IW8g9aN0

Why, you could hide the electrical links for the trailer lights in the link itself with leaf/pin-contacts, seeing as the 5th wheel stays connected.

Anyone else?

WhiteWolf McBride 05-01-2013 01:13 PM

Re: Does anyone make a Folding Gooseneck?
 
Then again, there is this monster...

http://www.youtube.com/watch?v=POoQTyWjHrk

Joe, want one for hauling the beasts out of your basement?

Apparently its an RGS-225 'TowHaul' (and its not the biggest one they make either!)

http://www.towhaul.com/

When ya just need the Biggest tow-rigs and lowboys around... (oh neat, they also have their own toy store! Ow, 1:50 of the beast is $219!)

WhiteWolf

dabears 05-01-2013 10:59 PM

Re: Does anyone make a Folding Gooseneck?
 
http://www.youtube.com/watch?v=HaHNQcfD5aI
I wanna see this done!

doodlebug 05-01-2013 11:43 PM

Re: Does anyone make a Folding Gooseneck?
 
Quote:

Originally Posted by dabears (Post 85903)

See this thread, http://rctruckandconstruction.com/sh...tire+inflation /
Cheer's, Neil.

Lmackattack 05-02-2013 12:52 AM

Re: Does anyone make a Folding Gooseneck?
 
Always liked how low the folding trailers are and it looks so easy to drive anything onto them but that's the only bonus I see with them.... the need for frame rail ramps,a winch add lots of weight to a truck that already has a wet kit... Personaly I like the Hyd detach goose neck myself. I timed my self the other day. 1min to stop,get out unhook air lines from deck, drop deck,stinger down, unlock pin ,back in truck and pull away from deck. It takes longer for the air in my tractor bags to drop than it takes me to disconnect from the deck...

Straywolf 05-02-2013 02:27 PM

Re: Does anyone make a Folding Gooseneck?
 
If i had the know how and tools i would love to try to build a folding gooseneck even if it wasnt hydro, manual with a wench would be cool. I wish there was one of these made in a kit form.

Mike

Lil Giants 05-12-2013 12:31 AM

Re: Does anyone make a Folding Gooseneck?
 
Quote:

Originally Posted by dabears (Post 85903)

Search out the username Ulrich on this forum, a fellow hobbyist from Germany currently has one under construction, I think he's nearly finnished & 90% works exactly like the life size. :cool:


All times are GMT -4. The time now is 02:36 PM.

Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.