|
Euro Style Trucks and Trailers A place for the Euro style trucks single and twin axle trucks and trailers... |
|
Thread Tools | Display Modes |
|
#1
|
||||
|
||||
Tamiya Arocs tipper
hi I am in the process of building the tamiya Arocs tipper with the MFC-03 and the actuator set here is a link to a few pictures not in order
https://postimg.cc/gallery/5tJvnKc |
#2
|
||||
|
||||
Re: Tamiya Arocs tipper
|
#3
|
||||
|
||||
Re: Tamiya Arocs tipper
|
#4
|
||||
|
||||
Re: Tamiya Arocs tipper
steering mod using a mount from KK truck store in the UK, I did the mod this way because the euro trucks have the steering servo on the L/H side of the chassis and I wanted it next to the gear change servo to eliminate the steering slop, if Tamiya had given the steering a bit more thought they would have had given you a great model straight from the box.
Last edited by Brel; 05-02-2021 at 03:28 AM. |
#5
|
||||
|
||||
Re: Tamiya Arocs tipper
|
#6
|
|||
|
|||
Re: Tamiya Arocs tipper
One very nice build there!
Not sure if it is allowed to comment in this section. I see that no one has commented and I am a bit worried cause this is a great truck and it deserves more attention! - mods please obliterate my post and let me know if I can post elsewhere in the comments section. |
#7
|
||||
|
||||
Re: Tamiya Arocs tipper
Very sharp truck! Great job fitting all that into a daycab
I don't remember seeing this when it was first posted
__________________
What do ya mean "Cars are neither Trucks or Construction"? It's still scale, and i play fairly well with others, most of the time... |
#8
|
|||
|
|||
Re: Tamiya Arocs tipper
I as well didn't see this when it was originally posted. Perhaps it was one of teh times when I was on a hiatus from teh computer, & when I FINALLY got back on it was deeply buried.
|
#9
|
||||
|
||||
Re: Tamiya Arocs tipper
Quote:
thanks frizzen and skeeter, it was a bit of a pain squeezing the electronics into the cab, but it works fine I changed the drive spindle and ram in the lift actuator for one with a courser thread because the original on took 1 minute to raise the bed and another to lower it, it will now lift up in thirty seconds and the same for down which will have to do, the kit supplied drive shaft is on the left and the coarser replacement is on the right and lifts the dump body up twice as fast trewq, thanks, I don't mind anyone commenting on my post and do appreciate positive comments Last edited by Brel; 06-15-2021 at 05:12 PM. |
#10
|
||||
|
||||
Re: Tamiya Arocs tipper
after much thought I decide to remove the Tamiya MF03 and replace it with a Servonaut M24 ESC and SM3 sound card with SM-EQ bass\treble boost to tweak the sound to match the trucks cab where the speaker is mounted in the roof. I also replaced the Tamiya 4 ohm speaker with a Visaton 8 ohm FRS 7, also replaced all of the Tamiya LED's with servonaut light boards which give a much better light output, I did not photograph the rear light boards because the were a pain to fit and I forgot to
new ESC and sound module new front light boards Last edited by Brel; 08-06-2021 at 02:06 PM. |
#11
|
||||
|
||||
Re: Tamiya Arocs tipper
|
#12
|
|||
|
|||
Re: Tamiya Arocs tipper
Very clean build... I really like the silver paint scheme ...
|
#13
|
||||
|
||||
Re: Tamiya Arocs tipper
thanks for your kind words
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|