#1821
|
||||
|
||||
Re: Great Dane excavating co.
It's a haul truck not a race truck. Your lifting the
Heaviest load out anybody here. Leave well enough alone |
#1822
|
||||
|
||||
Re: Great Dane excavating co.
What is the # on the Jung pump? What do you have the pressure set at?
__________________
Sharing knowledge is one thing that defies basic arithmetic logic --- the more you share, the more you get! Joe |
#1823
|
||||
|
||||
Re: Great Dane excavating co.
I thought it dumped just fine . Maybe open your fitting ports like Reg said .
__________________
RIP FreddyGearDrive 2-12-59/12-19-11 To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. |
#1824
|
||||
|
||||
Re: Great Dane excavating co.
__________________
Always wasting money, as the wife says. To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. |
#1825
|
||||
|
||||
Re: Great Dane excavating co.
Sweeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeetttttttttttttt tt!
|
#1826
|
||||
|
||||
Re: Great Dane excavating co.
WOWWWWWWWWWWWWWWWWWW
|
#1827
|
||||
|
||||
Re: Great Dane excavating co.
Sweet "Knockers" The whole thing is sweet Lot of Lovin put in to this MegaMachine.
|
#1828
|
||||
|
||||
Re: Great Dane excavating co.
Awsome ....the fine detail makes these models stand out ...nice ..How is the tapping going so far ..I have been doing quite a bit of 0-80 latley and it seems almost easier then the 2-56 and 4-40 ..Broke 2 2-56 on this my scraper build and one 1-72 ..2 of them were because I dropped them ..lol
I have to found some pretty good deals on Ebay for taps but should start looking for some good drill bits..my local suppler is charging over $5 a piece for the smaller bits ..they are good bits tho .. Nice work buddy |
#1829
|
||||
|
||||
Re: Great Dane excavating co.
If I would have planned ahead,,,,,,,, I wouldn't have to make simple tools like this!! Had to make an extension for drill bit and tap for holes along bed rails. Hand drilled. Haven't broken any bits or taps for a long time but most of the small ines I've broken have been from dropping them also!!! The first ring of bolts on the wheels are just for show, drilled a little under and just pressed them in. Every time I think I'm close to paint I realize another detail that would look good, feels like never ending!! Like this hitch, have to tear the back end out to get in mill for cutting/tapping. Then thinking about small things like supports for wire to lights ect,,,, but I've learned if I don't do it now I don't do it. Still have lights for excavator laying around that I keep saying I'll get to!,,,,,,
__________________
Always wasting money, as the wife says. To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. |
#1830
|
||||
|
||||
Re: Great Dane excavating co.
Quote:
Kerst |
#1831
|
||||
|
||||
Re: Great Dane excavating co.
is it going to be yellow for cabin fever???
|
#1832
|
||||
|
||||
Re: Great Dane excavating co.
Hopefully be yellow within next few weeks.
__________________
Always wasting money, as the wife says. To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. |
#1833
|
||||
|
||||
Re: Great Dane excavating co.
The trucks looking real good RW!
|
#1834
|
||||
|
||||
Re: Great Dane excavating co.
Wow you got that together fast.
|
#1835
|
||||
|
||||
Re: Great Dane excavating co.
Got to McMaster.com for your drill bits. You can get cheap ones or get the better ones much cheaper than from anyone local.
__________________
LYNN |
#1836
|
||||
|
||||
Re: Great Dane excavating co.
Much better in quality too . I get mine in packs of 12 .
__________________
RIP FreddyGearDrive 2-12-59/12-19-11 To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. |
#1837
|
||||
|
||||
Re: Great Dane excavating co.
New gears arrived today, just in time for tear down for paint. Ihave 144:1 reduction and with these new gears I can change to 108:1 That might be a little closer to scale speed. Also can go to 81:1 (or 96:1) but I think that will drastically drop my torque and be too fast.
Paint time, was going to go with new cat yellow but I have several cans of old cat yellow. Oh well it will match the fleet.
__________________
Always wasting money, as the wife says. To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. |
#1838
|
||||
|
||||
Re: Great Dane excavating co.
OK when did they change they're yellow again I notice 2 shades at Cat Monday but didn't think to ask .
__________________
RIP FreddyGearDrive 2-12-59/12-19-11 To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. |
#1839
|
||||
|
||||
Re: Great Dane excavating co.
I think they only have the two, the new yellow is more dark than the old. Probably been 10-12 years or more for the new paint.
__________________
Always wasting money, as the wife says. To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. |
#1840
|
||||
|
||||
Re: Great Dane excavating co.
One looks more mustardy
|
Currently Active Users Viewing This Thread: 22 (0 members and 22 guests) | |
|
|