|
Farm Tractors and Implements Discussion of farm equipment |
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
John Deere 9520T - 1/16
Here is a little progress on the 9020T tractor I am working on.
Belttension is designed with bearings in the 'forks' instead of placing them in the wheels. The walking beam is now done. On the pictures you will see how I made the attachments to the frames. The issue is that, by moving the two frames up and down from center/zero the distance is getting bigger and when the beam is attached, it forces the frames to move inward and therefore no longer parallel. I came up with the idea, that if I let it 'rotate' over a square piece, it would spread the frames when the beam travels up and down. Also the beam will be able to travel backward (about 1.5mm) on the mid axle. As this distance also get's shorter. Next up is the gearbox. Comments are welcome :-) Anders Kolpen |
#2
|
|||
|
|||
Re: John Deere 9520T - 1/16
More pics:
Mainframe is milled out to make room for transmission and rearaxles. Left and right side of the undercarriage is almost done. |
#3
|
||||
|
||||
Re: John Deere 9520T - 1/16
Kolp- Thanks for coming over to this new forum and sharing your builds. I saw this new build on modelltruck and it is a huge leap forward from your previous one.
|
#4
|
||||
|
||||
Re: John Deere 9520T - 1/16
Wow! I remember drooling over your other RC tractor designs, but you've really taken it to a whole new level with this latest post! Looks amazing! I expect this will be your best performing tractor to date.
__________________
Nathan |
#5
|
||||
|
||||
Re: John Deere 9520T - 1/16
Gonna be another amazing build. I wish I had the knowledge and resources to convert my CAT Challenger like that.
Ben |
#6
|
|||
|
|||
Re: John Deere 9520T - 1/16
Hi Anders
thanks for bringing your fantastic builds over to this site
__________________
Daniel |
#7
|
||||
|
||||
Re: John Deere 9520T - 1/16
Anders, welcome a-board
Those tracks, are they the gel-type or the stiff vinyl type?
__________________
Giving up is not an option!!! Rob |
#8
|
|||
|
|||
Re: John Deere 9520T - 1/16
Thank you all.
Rob >> I have them both. The gel types seems way better than the hard plastics. But we will see how they act when they are mounted. Anders |
#9
|
|||
|
|||
Re: John Deere 9520T - 1/16
Quote:
I'm looking forward for the 1st testrun!! |
#10
|
||||
|
||||
Re: John Deere 9520T - 1/16
wow @ the roller setup!
__________________
Rc's are like pringles. You can't have just one!! my YouTube is - To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. Subscribe!! My Facebook - To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. |
#11
|
|||
|
|||
Re: John Deere 9520T - 1/16
you have a lot of work in the roller assy. I can't wait till the rest of the tractor is done.
|
#12
|
||||
|
||||
Re: John Deere 9520T - 1/16
Wow! Really nice work.
__________________
Scott "No load is too Small" |
#13
|
||||
|
||||
Re: John Deere 9520T - 1/16
I don't know how the 1:1 is done but on my old Caterpillar tractors the equalizer bar or spring sits in a saddle and can float sideways but trapped under a pin to prevent the powertrain from going over.
Anyway,Very nice milling work. I like the way you made that ball setup. |
#14
|
|||
|
|||
Re: John Deere 9520T - 1/16
So here is the latest activity from my workbench.
The undercarriage and transmission of the 9520T tractor is finally taking shape. Trackframes has been done for a while, just some small touch ups here. Transmission though is now nearly complete and fits perfectly inside the mainframe. As you will see on the back, I have drilled the holes for all the bolts to fit either a 3pt hitch or a wide swing bar. I am not sure what to make yet. I better start with the swing bar as I want to get the rig pulling as soon as possible. Not much to say, as the pics will tell you the most |
#15
|
||||
|
||||
Re: John Deere 9520T - 1/16
"Not much to say, as the pics will tell you the most"
and **** do they say allot! this is a super build!
__________________
Rc's are like pringles. You can't have just one!! my YouTube is - To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. Subscribe!! My Facebook - To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. |
#16
|
|||
|
|||
Re: John Deere 9520T - 1/16
This is some very nice work you have done a lot of detail is added. Ed
|
#17
|
|||
|
|||
Re: John Deere 9520T - 1/16
Wow, that's impressive! You do amazing work. Did you mill the bevel gears in the transmission or buy them. You can buy these type of gears at SDP-SI but they are not inexpensive and they charge a lot for shipping.
|
#18
|
||||
|
||||
Re: John Deere 9520T - 1/16
Simply awesome.
__________________
Scott "No load is too Small" |
#19
|
||||
|
||||
Re: John Deere 9520T - 1/16
Absolutely great build! Workmanship and engineering are awesome. Can't wait to see it go!
Ken |
#20
|
||||
|
||||
Re: John Deere 9520T - 1/16
You have built the best RC conversion ever! Very nice!
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|