![]() |
|
Construction Equipment If it digs, pushes, hauls dirt "off road" post it here. |
![]() |
|
Thread Tools | Display Modes |
#41
|
||||
|
||||
![]()
She comes with decals.......
|
#42
|
||||
|
||||
![]()
Makin a dozer blade!
![]() |
#43
|
||||
|
||||
![]()
Ooohhhh - snifty - is this for the coming snow fall?
|
#44
|
||||
|
||||
![]()
Would definitely work for that. More so for all the dirt/sand I'm going to be dumping in my basement!!
|
#45
|
||||
|
||||
![]()
You're filling your basement with dirt/sand?! And doing it thru a window with the rc's?
'at a boy! ![]() |
#46
|
||||
|
||||
![]()
Just need to mount the quick detach plate now! It's 4:45am....must have been the TURKEY POWER!!!! I think it turned out good considering I didn't have any drawings/plans. Even tacked on a consumable blade edge.
![]() |
#47
|
||||
|
||||
![]()
Front and rear driveshafts are binding bad when fully steered left and right. Completely stalls the motor when in reverse.
Anyone experience this with this model? Should I just take out the shafts and file the u-joints? Haven't been driving this **** thing long enough for driveline problems ![]() |
#48
|
|||
|
|||
![]()
do u have the pot metal u-joints or the zinc plated steel ones? I had similar issues with my 966g when the pot metal joints where used. In the hinge area plates are there chunks of brass around the pins?
|
#49
|
||||
|
||||
![]()
No brass shavings and the u-joints look to be pot metal.
|
#50
|
|||
|
|||
![]()
can u post a pic of the loader hinge area to help me get u the right answer to ur problem?
|
#51
|
||||
|
||||
![]()
Top hinge:
![]() There is a very slight amount of play in the hinge. Maybe a millimeter. Driveshaft/Bottom hinge: ![]() You can see how the u-joints are wearing on the edge of the sphere. I suspect that to be the issue. It's not limited to the front or the rear shaft either. When I disconnect one or the other it will still stall. Need a temp fix. I'll probably put some different shafts in entirely. I've always had great success with the MIP stuff. Might have to customize something to fit. |
#52
|
||||
|
||||
![]()
I'd say get rid of that shaft and get a real u joint . thats the most micky mouse joint I've seen ( no offense ) pot metal will not last long under torsional stress . is there a slider on the shaft ?
__________________
RIP FreddyGearDrive 2-12-59/12-19-11 To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. |
#53
|
||||
|
||||
![]()
these joints are a bit on the weak side - but it does look like that joint is noy fully engaged at the ball. right side looks slightly open.
mine have held up without issue - ive heard of guys swapping the systgem out. |
#54
|
||||
|
||||
![]()
Also - you need to keep that ball directly over the center of the hinge pin - so loosen the set screw on that right half and adjust.
|
#55
|
|||
|
|||
![]()
upgrade to the steel zinc coated u-joints. I did that and upgraded to new plate with brass like u have already. U have some worn out pot metal u-joints. U will need to order two sets of wedico number 2017 u-joints.
![]() |
#56
|
||||
|
||||
![]()
Cool will adjust for now and get those ordered up!
Thanks gents! Start thinking about when you guys want to bring your stuff over for some weekend mini-fun. Last edited by Roadmasters; 12-03-2011 at 05:28 PM. |
#57
|
||||
|
||||
![]()
ya got crash space .... for us Indiana guys thats a chair to sit in for a few minute or so .... LOL
|
#58
|
||||
|
||||
![]()
Well shoot, i never knew you were in monticello... i have an aunt and uncle that live there and I'm just a couple hours west..
-J.D. |
#59
|
||||
|
||||
![]()
Yup, wonder if I know them I grew up here.
I have 2 spare bedrooms a foldout couch and airbed as well. I'm 2.5 hours from Indy for reference. |
#60
|
||||
|
||||
![]()
Where can I get Leimbach parts? I broke the drive coupler off the motor somehow. I guess this loader is cursed! Should have some video by now but I've been working on this bastard non-stop.
At least I have my fellow grown-up-sandbox nerds to help ![]() |
![]() |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|