|
Construction Equipment If it digs, pushes, hauls dirt "off road" post it here. |
|
Thread Tools | Display Modes |
#101
|
||||
|
||||
Re: Liebherr 574
I just held them in the vice on my mill and manually machined them. It took a while.lol
|
#102
|
|||
|
|||
Re: Liebherr 574
hmmm thats what i got to look forward to next then, i have to go to my fathers tomorrow to use his mill.
|
#103
|
||||
|
||||
Re: Liebherr 574
It's not so bad when you are just doing it for yourself. I have had a few requests to make these buckets again but it really isn't cost effective for me or the customer when I am hand machining each tooth.lol It's much cheaper to buy a mass produced bucket from Magom HRC or do what you are doing and make your own. I would need to charge $250+ for a bucket and no one will want to pay that because there are cheaper alternatives.
Keep up the great work on your conversion! |
#104
|
|||
|
|||
Re: Liebherr 574
Hi there,
I hope it is ok to post as form old from 2011. What a great build. Iam going to do the same. I realise someone already asked the question. But iam looking at the Actuators but cant seem to find those ones can you please direct me to the site that you bought from. I found this site http://www.firgelli.com/L12_R_Linear...ol_p/l12-r.htm but can't find those sizes you stated. Greatly appreciated Brina |
#105
|
||||
|
||||
Re: Liebherr 574
I'm using the non RC type. L12-S http://www.firgelli.com/L12_S_Micro_...es_p/l12-s.htm
|
#106
|
|||
|
|||
Re: Liebherr 574
Hi RCP57, thanks heaps for that. For a wonder what stroke and ratio would you recommend and how many will i need.Thanks Brian
|
#107
|
|||
|
|||
Re: Liebherr 574
Nice Reg, just looked through this thread
__________________
Not trolling anymore... To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. |
#108
|
||||
|
||||
Re: Liebherr 574
Thanks Calvin. It is one of my favorite toys.
|
#109
|
|||
|
|||
Re: Liebherr 574
Made a offer on a carson track loader. Guy said he'll get back to me, if he doesn't take it I'm going to get the new Magom all metal 574 wheel loader.
__________________
Not trolling anymore... To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. |
#110
|
||||
|
||||
Re: Liebherr 574
Reg,
I had to go thru the entire thread again, really nice job! Love the rims and the bucket! Question for you, did you consider separating the left and right side motors and adding a mix on the steering to control wheel spin? Wonder if anyone has done it that way? Would it add anything to the maneuverability or traction when pushing into a pile? Thanks for all the info! Jim |
#111
|
|||
|
|||
Re: Liebherr 574
Quote:
Also I was planning on testing out the new P16 actuators from Firgelli: - http://www.actuonix.com/P16_Actuators_s/1861.htm Stein :-) |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|