|
|
|||||||
| Welcome New Members A place to introduce yourself to the membership. |
 |
|
|
Thread Tools | Display Modes |
|
#1
02-27-2012, 04:41 PM
|
|||
|
|||
Hello from Colorado (south of Denver)
Hi All,
I only receintly discovered that RC could be done with Semis and Construction equipment. I must say this site is the most informitive I have seen so far for this. A Little background - been doing RC (started with cars) sense 1984 - a lot has changed... (done Cars, trucks, copters, planes, Quad copters and more I even have an RC snowmobile)... oh yes-- I have a small industral laser as well - how I got to the name RCLaser. I hope to get some good advise (I have seen a lot of good advise so far) in getting started.... (like where should I start- Tamiya? Globe liners seems like a good start...) Anyone out there live in Colorado... I would love to see these in action up close. Warmest Regards, RCLaser 
|
|
#2
02-27-2012, 05:49 PM
|
||||
|
||||
|
Re: Hello from Colorado (south of Denver)
Welcome,
The only person in Colorado on this forum that actually has trucks is roadranger. Nice to see another Coloradan on the forums!
__________________
RIP FGD 12-19-11 To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
|
|
#4
02-28-2012, 12:41 PM
|
|||
|
|||
|
Re: Hello from Colorado (south of Denver)
Thanks for the Welcomes'!
The laser is a 30Watt.. Yes -it can do pictures on wood, anadized aluminum, leather, acrylic, cardboard and other materials. It can also cut thin materials. (it does not cut any metals though  )
|
|
#5
02-28-2012, 05:41 PM
|
||||
|
||||
|
Re: Hello from Colorado (south of Denver)
Oh a laser that can cut styrene that would be handy to cut out my body pieces. Too bad it's in Colorado and I'm in OH
Welcome aboard to the best rc truck,and construction,site. --Dan
__________________
To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
|
|
#6
02-29-2012, 04:22 PM
|
|||
|
|||
|
Re: Hello from Colorado (south of Denver)
Thanks scalelover..
I have learned a lot so far from this site. ... hmm.. haven't tried Styrene yet... will pick some up and give it a shot on the laser.. guessing it should work well.
|
|
#7
03-02-2012, 02:51 AM
|
||||
|
||||
|
Re: Hello from Colorado (south of Denver)
Welcome to the board.
__________________
To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. Mike "DREAMWEAVER" Johnson To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. RIP FreddyGearDrive 2-12-59/12-19-11 Rims and Tanks by ihbuilder / Grill and Visor by Brian in PA / Mirrors, Front and Rear Bumper, Back of Cab Lights, and Steering Arms by tc1cat / Fenders by Stylin n Profilin / Frame Rails by The Late Freddy Gear Drive
|
|
#8
03-07-2012, 12:07 PM
|
|||
|
|||
|
Re: Hello from Colorado (south of Denver)
Well Dan, I gave it a try... could do with a little tuning but the laser does cut styrene... (Styrene is pretty dense... makes it harder to cut but it works)
Now all I have to do is figure out what I want to cut and build from Styrene..!!  Laser cutting Styrene Sample Pic
|
|
| Tags |
| new member, newbee |
| Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|
Linear Mode
