Great Dane excavating co.

[bigford]

It's a haul truck not a race truck. Your lifting the
Heaviest load out anybody here. Leave well enough alone

[Lil Giants]

What is the # on the Jung pump? What do you have the pressure set at?

[ihbuilder]

I thought it dumped just fine . Maybe open your fitting ports like Reg said .

[Cooper]

Some more work

Rock knockers



Mud flaps


Rims more detailed



And some rock guards in the bed

[RCP57]

Sweeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeetttttttttttttt tt!

[bigford]

WOWWWWWWWWWWWWWWWWWW

[Bo Wallen]

Sweet "Knockers" The whole thing is sweet Lot of Lovin put in to this MegaMachine.

[tracksntreadslou]

Awsome ....the fine detail makes these models stand out ...nice ..How is the tapping going so far ..I have been doing quite a bit of 0-80 latley and it seems almost easier then the 2-56 and 4-40 ..Broke 2 2-56 on this my scraper build and one 1-72 ..2 of them were because I dropped them ..lol
I have to found some pretty good deals on Ebay for taps but should start looking for some good drill bits..my local suppler is charging over $5 a piece for the smaller bits ..they are good bits tho ..
Nice work buddy

[Cooper]

If I would have planned ahead,,,,,,,, I wouldn't have to make simple tools like this!! Had to make an extension for drill bit and tap for holes along bed rails. Hand drilled. Haven't broken any bits or taps for a long time but most of the small ines I've broken have been from dropping them also!!! The first ring of bolts on the wheels are just for show, drilled a little under and just pressed them in. Every time I think I'm close to paint I realize another detail that would look good, feels like never ending!!



Like this hitch, have to tear the back end out to get in mill for cutting/tapping. Then thinking about small things like supports for wire to lights ect,,,, but I've learned if I don't do it now I don't do it. Still have lights for excavator laying around that I keep saying I'll get to!,,,,,,

[kerst]

Originally Posted by Cooper

If I would have planned ahead,,,,,,,, I wouldn't have to make simple tools like this!! Had to make an extension for drill bit and tap for holes along bed rails. Hand drilled. Haven't broken any bits or taps for a long time but most of the small ines I've broken have been from dropping them also!!! The first ring of bolts on the wheels are just for show, drilled a little under and just pressed them in. Every time I think I'm close to paint I realize another detail that would look good, feels like never ending!!

I have done that, after thinking a few hours how on earth to reach such a spot and it took only minutes to make a simple extension.

Kerst

[bigford]

is it going to be yellow for cabin fever???

[Cooper]

Hopefully be yellow within next few weeks.

[TRUCKMAKER]

The trucks looking real good RW!

[TRUCKMAKER]

Wow you got that together fast.

[tc1cat]

Got to McMaster.com for your drill bits. You can get cheap ones or get the better ones much cheaper than from anyone local.

[ihbuilder]

Originally Posted by tc1cat

Got to McMaster.com for your drill bits. You can get cheap ones or get the better ones much cheaper than from anyone local.

Much better in quality too . I get mine in packs of 12 .

[Cooper]

New gears arrived today, just in time for tear down for paint. Ihave 144:1 reduction and with these new gears I can change to 108:1 That might be a little closer to scale speed. Also can go to 81:1 (or 96:1) but I think that will drastically drop my torque and be too fast.




Paint time, was going to go with new cat yellow but I have several cans of old cat yellow. Oh well it will match the fleet.

[ihbuilder]

OK when did they change they're yellow again I notice 2 shades at Cat Monday but didn't think to ask .

[Cooper]

I think they only have the two, the new yellow is more dark than the old. Probably been 10-12 years or more for the new paint.

[bigford]

One looks more mustardy