new scania project-need help with servonaut vs MFC

[aussietruckerguy]

Hi there,
Im looking at a new rig to go with my single drive scania. It will be a twin drive scania set up for a road train using two home built or tamiya reefer's. Im not liking the restrictions on the tamiya MFC as far as lights, I want marker's six-eight per side, two side indicators, between two and four each on the rear, four stops. Then I also need the lights on the dolly. Also be able to drive the leg motors on both trailers driven off Rx. Also extra lights on the prime mover with the marker and fog lights on the rack above the windscreen. The key question is will servonaut will be able to do this, or am I going to home brew some- all of the electronics. The vibration is not a want, as I use trucks all the time and it does not vibrate that much. Plus I have no idea how to do sound outputs on the truck. thanks for any help

[Actros861]

Yes you can, on my Scania R620 i have approximately 180 LEd's.
And the best thing with Servonaut is the drivingexperience its so much better then the MFU

[aussietruckerguy]

thanks what would be the starting setup for what I want?

[Actros861]

Without cruisecontrol
S20, ML4, MM4 and SMX

With cruisecontrol
M20+, MM4 and SMX

[aussietruckerguy]

thanks, anyone know how to get these in Australia, I was on garden trucking and there out of stock for the AIR-U.

[aussietruckerguy]

Well the R620 and a reefer trailer is ordered out of hong kong, just it time for my birthday

[Quad-Dog]

That is what you need german relatives for
Have you asked servonaut? I bet they sell those things all over the world.

[aussietruckerguy]

I have, I'm waiting for the reply, worst case ill talk to my cousins in the U.K.

[Brel]

servonaut do not take pay pal, they only take a credit card or bank transfer for payment, I had to ring them with my car number when I ordered from them

[apfubar]

You can order them from doc gear... He accepts PayPal...

There is also TTM (not sure about PayPal), and Scale Art(just don't look at the models, the truck prices are scary, the detail however is drool worthy)...

Cheers,
AP
p.s I have ordered from all three, and have received the products here in Sydney.

[aussietruckerguy]

have you got the web address for TTM and Doc Gear or how to get in contact, Scale Art have some great kit but not the sevonaut gear I'm looking for

[Brel]

here is the link to the ttm shop
http://www.ttm-shop.de/

[apfubar]

Doc gear is:
http://www.der-getriebedoktor.de/

Ap

[Espeefan]

Originally Posted by Actros861

Without cruisecontrol
S20, ML4, MM4 and SMX

With cruisecontrol
M20+, MM4 and SMX

Do you like the cruise control feature? Personally, I'd rather have the more conventional throttle, returning to neutral, when you let go of the stick. It's just what I've always had on all my RC models.

[Actros861]

Originally Posted by Espeefan

Do you like the cruise control feature? Personally, I'd rather have the more conventional throttle, returning to neutral, when you let go of the stick. It's just what I've always had on all my RC models.

Yes i do, it's a bit confusing in the beginning but after a short time of driving it becomes natural.
I have three trucks with M20+ and i think that is the best ESC on the market, the MFU is absolutely crap in comparison. S20 isn't bad either, i have that in my CAT 966

[extremetrucksaus]

Hi If you looking for servonaut stuff try www.csmi.com.au they are the dealers for servonaut in Australia

[DoubleClutchin']

Can you run the servonaut system with digital trims or do you need analog like the Tamiya MFU?

[egronvold]

Originally Posted by DoubleClutchin'

Can you run the servonaut system with digital trims or do you need analog like the Tamiya MFU?

You don't use trims to operate the Servonaut products.

[egronvold]

Originally Posted by aussietruckerguy

thanks, anyone know how to get these in Australia, I was on garden trucking and there out of stock for the AIR-U.

NB! AIR-U is used with S20 (or MFU), AIR-4 with M20+ And K30/ K40.

[DoubleClutchin']

Originally Posted by egronvold

You don't use trims to operate the Servonaut products.

How many channels do you need? Can I use my KO wheel radio ?