RC Truck and Construction  

Go Back   RC Truck and Construction > RC Tech section. > Metal forming & tools

Metal forming & tools If it bends,twists,welds,cuts & turns metal.Post it here


Reply
 
Thread Tools Display Modes
  #1  
Old 06-11-2013, 09:31 AM
Rvjimd's Avatar
Rvjimd Rvjimd is offline
Craftsman
 
Join Date: Dec 2012
Location: Des Moines, Iowa
Posts: 884
Rvjimd is on a distinguished road
Default Center drilling hole in dowel?

I have started searching the web and thoughts would check with you guys as well.

I working on my first conveyer and want to drill a hole thru the center of a dowel. The dowel will be the roller at each end of the conveyer and I may also use them along the conveyer as belt supports.

I don't have a lathe yet, sounds like that is the best way to do this.

My drill press chuck does not open quite wide enough to get the dowel in it. I was going to try that.

The dowel is about 1" long and 5/8" diameter.



Maybe instead of searching for how to do this I will search for a descent table top lathe. Any tips on that sort of lathe is also welcome.


Thanks for any tips!

Jim

Last edited by Rvjimd; 06-11-2013 at 09:32 AM. Reason: Typo
Reply With Quote
  #2  
Old 06-11-2013, 09:45 AM
louie r/c nut louie r/c nut is offline
Newbie
 
Join Date: May 2013
Location: Queens N.Y
Posts: 116
louie r/c nut is on a distinguished road
Default Re: Center drilling hole in dowel?

Hey Jim you might want to set up a jig and use your drill press .

Take a scrap piece of ply wood cut a 5/8 hole stick the rowel in the hole then line it up to the drill press clamp the ply down so it does not move then drill .

Drill very slow so you don't crack the rowel should have no problem .

I have done this for parts on my boats and it has worked well .
Reply With Quote
  #3  
Old 06-11-2013, 09:49 AM
Rvjimd's Avatar
Rvjimd Rvjimd is offline
Craftsman
 
Join Date: Dec 2012
Location: Des Moines, Iowa
Posts: 884
Rvjimd is on a distinguished road
Default Re: Center drilling hole in dowel?

Louie,

I have a clamping fixture for the press, but I am having trouble getting the hole started in the center.

Any advice on simply marking the center? And then, is there a special bit I should be using to drill the hole so it won't wander?

Thanks

Jim
Reply With Quote
  #4  
Old 06-11-2013, 10:01 AM
louie r/c nut louie r/c nut is offline
Newbie
 
Join Date: May 2013
Location: Queens N.Y
Posts: 116
louie r/c nut is on a distinguished road
Default Re: Center drilling hole in dowel?

5/8" is pretty wide what size whole are you looking to make in the rowel .

If it is walking on you you can use a body remer or an ice pick to get it started .

Also it a good idea to use a good wood bit make sure it is sharp this way you can drill slow .

Finding the center is a little tricky I do it mostly by eye you will have to dill a few as test pieces as long as you get it close and make them all the same you should be fine .
Reply With Quote
  #5  
Old 06-11-2013, 10:05 AM
Rvjimd's Avatar
Rvjimd Rvjimd is offline
Craftsman
 
Join Date: Dec 2012
Location: Des Moines, Iowa
Posts: 884
Rvjimd is on a distinguished road
Default Re: Center drilling hole in dowel?

I m trying to put 1/8 hole to start out. That may be the final size, or I may enlarge it for a bearing or bushing or drive gear. At this point 1/8" is what I'm trying.
Reply With Quote
  #6  
Old 06-11-2013, 10:07 AM
9W Monighan's Avatar
9W Monighan 9W Monighan is offline
Big Dawg On The Bone
 
Join Date: Aug 2010
Location: Pittsburgh,PA.
Posts: 1,283
9W Monighan will become famous soon enough9W Monighan will become famous soon enough
Default Re: Center drilling hole in dowel?

If you don't have a center head for your combination square ;A quick search on internet I found this picture.


Try some brad point drill bits so you keep the drill centered. The wood grain will pull a regular twist drill off center.
Reply With Quote
  #7  
Old 06-11-2013, 10:09 AM
Rvjimd's Avatar
Rvjimd Rvjimd is offline
Craftsman
 
Join Date: Dec 2012
Location: Des Moines, Iowa
Posts: 884
Rvjimd is on a distinguished road
Default Re: Center drilling hole in dowel?

Ah, that helps, I have all that stuff here, let me try that to at least find the center.

Thanks
Reply With Quote
  #8  
Old 06-11-2013, 10:39 AM
Dieselchopper's Avatar
Dieselchopper Dieselchopper is offline
Green Horn
 
Join Date: Oct 2012
Location: Estevan, Saskatchewan, Canada
Posts: 274
Dieselchopper is on a distinguished road
Default Re: Center drilling hole in dowel?

To give your drill bit a spot to start on a light tap with a centre punch to make a divot just like you would in metal. I mark thing out on round stock in steel all of the time just as in picture above. It does work well. You cannot beat the accuracy gained with a centre punch to start the hole unless you are on a lathe or mill.
Reply With Quote
  #9  
Old 06-11-2013, 12:10 PM
Rvjimd's Avatar
Rvjimd Rvjimd is offline
Craftsman
 
Join Date: Dec 2012
Location: Des Moines, Iowa
Posts: 884
Rvjimd is on a distinguished road
Default Re: Center drilling hole in dowel?

I think I found a way to get a good center hole.

I found it on a google search. You mount the bit just snug, upside down in the drill press. Then lower it down to the fixture on the base and get the base lined up and clamp the bit into the base fixture. This supposedly get the chuck in the center. On my setup it was not quite centered, probably my base is not perfectly true to the chuck and spindle.

Then, raise up the chuck leaving the bit in the bottom fixture. Mount the dowel in the chuck and drill.

Works pretty good. I wish I had a 5/8 chuck, cause I cant fit my 5/8 dowel that I wanted to use, but I think 1/2 is going to work.



I bet this is why somebody invented the lathe!

Thanks for the tips

Jim
Reply With Quote
  #10  
Old 06-13-2013, 01:47 AM
Espeefan's Avatar
Espeefan Espeefan is offline
Big Dawg On The Bone
 
Join Date: Aug 2010
Location: Wisconsin
Posts: 2,888
Espeefan has a spectacular aura aboutEspeefan has a spectacular aura aboutEspeefan has a spectacular aura about
Default Re: Center drilling hole in dowel?

That's actually a very handy tip, for doing a quick and dirty center hole into something round. Thanks for sharing it!
__________________
Nathan
Reply With Quote
  #11  
Old 08-29-2013, 04:42 PM
CrewCab59's Avatar
CrewCab59 CrewCab59 is offline
Newbie
 
Join Date: Jun 2012
Location: Knoxville, Tennessee
Posts: 40
CrewCab59 is on a distinguished road
Default Re: Center drilling hole in dowel?

A Bell Punch is a nice tool to find the center on round stock .
Attached Images
File Type: jpg bell punch.JPG (18.7 KB, 11 views)
Reply With Quote
  #12  
Old 09-06-2013, 02:53 AM
grumpygrady grumpygrady is offline
Green Horn
 
Join Date: Aug 2010
Location: florida
Posts: 263
grumpygrady is on a distinguished road
Default Re: Center drilling hole in dowel?

Quote:
Originally Posted by Rvjimd View Post
Louie,

I have a clamping fixture for the press, but I am having trouble getting the hole started in the center.

Any advice on simply marking the center? And then, is there a special bit I should be using to drill the hole so it won't wander?

Thanks

Jim
sure take a funnel and find a str8 punch that is tight in the opening of the funnel put funnel over dowel and mark with punch
Reply With Quote
  #13  
Old 09-06-2013, 02:54 AM
grumpygrady grumpygrady is offline
Green Horn
 
Join Date: Aug 2010
Location: florida
Posts: 263
grumpygrady is on a distinguished road
Default Re: Center drilling hole in dowel?

Quote:
Originally Posted by grumpygrady View Post
sure take a funnel and find a str8 punch that is tight in the opening of the funnel put funnel over dowel and mark with punch
lol or use a bell punch lol
Reply With Quote
  #14  
Old 09-06-2013, 02:21 PM
Radio Control Trucker's Avatar
Radio Control Trucker Radio Control Trucker is offline
Journeyman
 
Join Date: Jun 2011
Location: Riverside County, CA
Posts: 746
Radio Control Trucker is on a distinguished road
Talking Re: Center drilling hole in dowel?

If using a funnel to line it up - then why not a Dremel rotary tool to drill the hole

- RCT
__________________
WCMT Director -
To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.

"Keep the Shiny-side Up, the Dirty-side Down & Keep 'er to the Line."
Reply With Quote
  #15  
Old 09-06-2013, 04:11 PM
kaptain Jack's Avatar
kaptain Jack kaptain Jack is offline
Journeyman
 
Join Date: Jan 2012
Location: Toronto Canada
Posts: 613
kaptain Jack is on a distinguished road
Default Re: Center drilling hole in dowel?

Two things, first: Lee Valey tools sells center finders for different sizes of dowels,secondary: you have to use brad point drill bit (designed specifically for wood) to drill your dowel. Its long pointy tip helps to stay centered and borrow into the wood.
Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 01:40 AM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.