Re: Scania W.A. Prime Mover 1/14.5
 

that is a very nice scania and roadtrain. great work on the right hand drive dash
zak

Re: Scania W.A. Prime Mover 1/14.5
 

What can i say well **** hot :) like the trailer set up

Re: Scania W.A. Prime Mover 1/14.5
 

That is one good looking Scania! The first pic looks real!

Brian

Re: Scania W.A. Prime Mover 1/14.5
 

Thank you, nice that you like my model. I know a lot of work ahead of me.

Re: Scania W.A. Prime Mover 1/14.5
 

marcel, is there any chance that you can measure your exhaust and intake diameters on the headache rack, as i need that to model the same thing on my scania as im just a bit lost without finding good shots of the real thing online.

Thanks

Re: Scania W.A. Prime Mover 1/14.5
 

The Exhaust is the Original from Wedico Art. Nr. 464 i made new pipes with 10mm diameter, the Original from Wedico was to small and short.

The Intake "Snorkel" is 11mm high and 16mm wide, narrows to the rear
to 13,5mm. The diameter in the lower part is also 13.5mm. the Pipe to the Air Filter is 11 an 12mm in the diameter.

http://img228.imageshack.us/img228/6149/49131gm6.jpg

http://img228.imageshack.us/img228/9753/49181jm2.jpg

The mass is in Scale 1:14,5 (Wedico). I have only 2 pics for the Snorkel, one from OZ Scania (front view) and a Swiss Kenny (side view), I then converted these into the scale

I do not know precisely how they are, maybe there is someone here in the forum you just give the original mass.

Re: Scania W.A. Prime Mover 1/14.5
 

WOW! Just a great model, attention to detail is outstanding!

Thank you for posting your project,

Jim

Re: Scania W.A. Prime Mover 1/14.5
 

Absolutely fantastic!
Another great use for a Scania! Never thought it could look this good.


Big Run - And so the Scania grows on me... as does everything...

Re: Scania W.A. Prime Mover 1/14.5
 

Thanks for the dimensions, im amazed with the detail, only hope my tamiya scania can look as good as yours.

Re: Scania W.A. Prime Mover 1/14.5
 

great job on the truck
it is as close to looking like the real thing as you can get
if you have other builds please post them

Re: Scania W.A. Prime Mover 1/14.5
 

Thanks

At the moment no other Projekt at work. First, the trailers are finished. In planing is a CR16 8x8 dump truck.

A small detail is finished, the WA Custom Car-Plate.

http://img40.imageshack.us/img40/682/img6099c.jpg

Furthermore, a still photo from the last event in Switzerland.

http://img97.imageshack.us/img97/4029/img6444h.jpg

http://img135.imageshack.us/img135/8962/img6480n.jpg

http://img221.imageshack.us/img221/9696/img6505g.jpg

http://img12.imageshack.us/img12/6313/img6520u.jpg

Re: Scania W.A. Prime Mover 1/14.5
 

Love your 'LOADS' and the whole truck...

Re: Scania W.A. Prime Mover 1/14.5
 

After little Break, the construction goes on :rolleyes:

First a few pics from Events

http://img402.imageshack.us/img402/8120/img6994o.jpg

http://img819.imageshack.us/img819/4131/img7006z.jpg

http://img594.imageshack.us/img594/7198/69831.jpg

I made a little bit on the Trailers. The rear bumber for the Dolly and the Lead was milled by a 8mm Alu-platte.

http://img442.imageshack.us/img442/672/402ia.jpg

http://img441.imageshack.us/img441/3106/404c.jpg

http://img37.imageshack.us/img37/4412/405zc.jpg

For the 45" Trailer, i made alu-plates on the exist brass-bumber. the holes are for the LED because of the small mounting deep of the original rearlights.

http://img685.imageshack.us/img685/3879/409mt.jpg

http://img221.imageshack.us/img221/4481/411zm.jpg

I went for the rail construction aluminum holder.

http://img839.imageshack.us/img839/6403/428y.jpg

http://img38.imageshack.us/img38/6337/427pj.jpg

http://img801.imageshack.us/img801/9246/419m.jpg

Next, I have 106 brass holder soft solder :(

Re: Scania W.A. Prime Mover 1/14.5
 

WOW that bumper looks great!! I love your idea for your rail jig!

Re: Scania W.A. Prime Mover 1/14.5
 

Yet again Im amazed with the quality of your modelling!

Re: Scania W.A. Prime Mover 1/14.5
 

amazing work of art sir! my fav pics are the ones of the chassis in paint just sittin their waiting on the finishing touches!!thanks for sharing..

Re: Scania W.A. Prime Mover 1/14.5
 

Thank you,

Here are the result of the Rail after solder, i know i have lot of work to finish the Rail.

http://imageshack.us/a/img404/8509/44855559.jpg

http://imageshack.us/a/img69/6031/38835489.jpg

I made a second Toolbox for each Trailer with 2mm ABS.

http://imageshack.us/a/img338/1109/94296401.jpg

http://imageshack.us/a/img96/2969/13554430.jpg

The Tyre Carrier i dit it with 3mm brass.

http://imageshack.us/a/img833/641/84197348.jpg

http://imageshack.us/a/img818/3826/59549315.jpg

And 2 pics to see how it looks like.

http://imageshack.us/a/img4/750/16841470.jpg

http://imageshack.us/a/img707/7412/64040535.jpg

Re: Scania W.A. Prime Mover 1/14.5
 

Very nicely done! Quite the rig you got there.

Re: Scania W.A. Prime Mover 1/14.5
 

Nice scania.Great looking trailers.Awesome work,great details!

Re: Scania W.A. Prime Mover 1/14.5
 

u got my attention brother...best quality detail on a wedico...