Forum: Construction Equipment
12-04-2022, 11:27 AM
|
Replies: 35
Views: 36
Re: Wooldridge 1940s Bottom-Dump Truck
What the heck... give it a try it's easy to shorten them...
For whats it's worth I have the Euclid and the rock wagon.... if you have a question I can always dig them out and measure or check...
|
Forum: Truck Building Tech
12-03-2022, 12:50 PM
|
Replies: 8
Views: 9
Side mirrors
Just wondering.... I want to put side mirrors on my little dodge dump truck, if I push them out from the body so they would be far enough out to see past the dump bed they look kind of "odd" sticking...
|
Forum: Construction Equipment
12-03-2022, 12:44 PM
|
Replies: 35
Views: 36
Re: Wooldridge 1940s Bottom-Dump Truck
Now that you mention it.....looking at those chains, it looks like if the doors open any more they may over center then bind... Might be better if they open just a little less so they can't do...
|
Forum: Construction Equipment
12-02-2022, 09:52 AM
|
Replies: 35
Views: 36
|
Forum: Construction Equipment
11-27-2022, 03:25 PM
|
Replies: 98
Views: 19,664
Re: Build an Excavator from Scratch
I never thought about that ... but yeah I can see where you would need either a planetary gear or a worm gear to hold the boom in place once you stop swing...
I used a 90 degree worm drive motor in...
|
Forum: Construction Equipment
11-27-2022, 12:14 PM
|
Replies: 35
Views: 36
Re: Wooldridge 1940s Bottom-Dump Truck
LOL this should be good.!!!!!
Really want to see how you mount the motors and the rest of the electronics. Looks like the power unit might give you enough room...
|
Forum: Big Boys of the road 4x4/6x6/8x8/10x10 Trucks
11-27-2022, 12:09 PM
|
Replies: 26
Views: 27
|
Forum: Truck Building Tech
11-26-2022, 04:34 PM
|
Replies: 33
Views: 9,547
Re: Axle suggestions?
Looking at that link you posted the 6v and 12v motors have the same specs. Except the 6v motor pulls more current...
Plus like I said if you drive a 12v motor at 7.2v your 17rpm becomes about 10rpm...
|
Forum: Truck Building Tech
11-25-2022, 09:45 AM
|
Replies: 33
Views: 9,547
Re: Axle suggestions?
Based on your findings I wonder if a 23 or 30 rpm 6v would work... I've started ordering more 6v motors.
12v running on 7.2v cuts speed and torque almost in half... but a 6v running 7.2 give you...
|
Forum: Static Conversions
11-13-2022, 10:51 AM
|
Replies: 7
Views: 4,628
Re: Half baked ideas
Novel idea... the hard part is finding the right car in the right scale....watch Hobby Lobby one might turn up...
|
Forum: Euro Style Trucks and Trailers
11-08-2022, 08:53 AM
|
Replies: 23
Views: 7,873
Re: Scania 112
Really starting to come together...
I agree with you order a couple more parts, maybe reprint something, before I would redesign the whole chassis....
|
Forum: General Discussion
11-05-2022, 09:28 AM
|
Replies: 1
Views: 2
Re: cb antenna
Wow that's a tough one....
it would have to be TINY....is there a piece of plastic tubing small enough that you could cut a slot in the bottom then just slip the antenna in the top and glue it in...
|
Forum: Boats!
11-01-2022, 09:52 AM
|
Replies: 39
Views: 8,922
|
Forum: Construction Equipment
10-23-2022, 12:38 PM
|
Replies: 119
Views: 52,106
Re: Nylint michigan crane conversion, hopefully
The metal axles and wheels with the narrow tires are 152mm outside to outside edge... the crane is 149 and change inside edge to inside edge.
I have a set of 3d printed wheels that are 137mm wide...
|
Forum: Construction Equipment
10-21-2022, 03:55 PM
|
Replies: 119
Views: 52,106
|
Forum: Construction Equipment
10-11-2022, 03:51 PM
|
Replies: 119
Views: 52,106
Re: Nylint michigan crane conversion, hopefully
I was thinking about a cutoff wheel on a dremel as well....it's about the only thing small enough to get in there.... but that is "real" steel in them thar Nylints.. so it might take some time.......
|
Forum: Construction Equipment
10-10-2022, 04:50 PM
|
Replies: 119
Views: 52,106
Re: Nylint michigan crane conversion, hopefully
I have been pondering the same thing....As you have said the structure under the crane is 2 or 3 mm to narrow, and way to high, I've been trying to figure out how to cut those two pieces down to...
|
Forum: Boats!
10-06-2022, 08:58 PM
|
Replies: 39
Views: 8,922
|
Forum: Scale Buildings, Warehouses and Structures.
10-03-2022, 05:30 PM
|
Replies: 5
Views: 520
|
Forum: Scale Buildings, Warehouses and Structures.
10-02-2022, 11:14 AM
|
Replies: 5
Views: 520
|
Forum: Truck Building Tech
09-01-2022, 09:26 AM
|
Replies: 33
Views: 9,547
Re: Axle suggestions?
I use those redcat motors on my WPL motor/transfer case combos they work really well they add just enough speed....You can put a drop of solder on those press on gears to help hold them in place....
|
Forum: Farm Tractors and Implements
08-31-2022, 08:34 PM
|
Replies: 29
Views: 18,551
|
Forum: Construction Equipment
08-30-2022, 11:54 AM
|
Replies: 18
Views: 2,719
Re: Toprace211/Huina 1550 upgrade
OK, here are some close-ups of the boom servos
https://live.staticflickr.com/65535/52320700586_15872a4c00_z.jpg
https://live.staticflickr.com/65535/52321123389_426caf0a75_z.jpg
I painted them...
|
Forum: Announcements from head quarters
08-27-2022, 12:46 PM
|
Replies: 4
Views: 9,065
|
Forum: Boats!
08-24-2022, 04:30 PM
|
Replies: 39
Views: 8,922
Re: RC Benchy
This is going to be really fun when it's done....do you have a place to try it out...
|