|
|
|||||||
| Construction Equipment Tech Hydraulics, Electronics, General Engineering, ect in constr equip |
 |
|
|
Thread Tools | Display Modes |
|
|
|
#1
10-15-2014, 01:01 PM
|
|||
|
|||
Need a Track control switch for 4200 excavator
Sheared off left track control top pin on the radio that has a metal "spider arm" which controls the left track.
It is a three position spring loaded self centering switch that controls f/b movement on the tracks. Tried to solder in something similar looking I had but didn't work. (They are green colored and replaced dials on the stock radio I believe) The company may not be able to get me one to replace it and wondered if anybody knows where to get one or a link to something just like it that will work the same way? (hate to get another radio just for this one switch  Thanks guys!
|
|
#3
10-15-2014, 07:39 PM
|
|||
|
|||
|
Re: Need a Track control switch for 4200 excavator
Green working switch to right is for R track (next to red switch)
|
|
#4
10-15-2014, 08:18 PM
|
||||
|
||||
|
Re: Need a Track control switch for 4200 excavator
Xbox, play station controllers. It's been a while since I did something similar. I had radio apart and found out my fix was just some jb weld to reattach lever arm. But if I'm not mistaken the potentiometers are ones used in gimbals but a metal plate screwed to radio housing keeps it to one axis. Only one axis hooked up. Like I said it's been a while since I was inside that radio but I remember scraping some old game controllers gimbals and set aside for a later date. Pretty sure the reason I did that was from seeing them in that radio. As I spent a lot of time looking for a dial pot that self centers, single axis and could not find. At leas that small.
If memory serves correct, .
__________________
Always wasting money, as the wife says. To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
|
|
#5
10-15-2014, 08:46 PM
|
|||
|
|||
|
Re: Need a Track control switch for 4200 excavator
It seems to be only a single axis self centering for forward neutral backward
|
|
#6
10-15-2014, 09:32 PM
|
||||
|
||||
|
Re: Need a Track control switch for 4200 excavator
Don't know if it's on my end but I can't see the pics. (Bill and Steve are still fighting!!)
__________________
Always wasting money, as the wife says. To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
|
|
#7
10-15-2014, 10:34 PM
|
|||
|
|||
|
Re: Need a Track control switch for 4200 excavator
Tried another way with pictures..if not will try tomorrow..thanks guys!!!!
|
|
#8
10-17-2014, 11:57 PM
|
|||
|
|||
|
Re: Need a Track control switch for 4200 excavator
Pics edited to show hopefully
|
|
#9
10-18-2014, 01:57 AM
|
||||
|
||||
Re: Need a Track control switch for 4200 excavator
   Xbox
__________________
Always wasting money, as the wife says. To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
|
|
#10
10-18-2014, 01:59 AM
|
||||
|
||||
|
Re: Need a Track control switch for 4200 excavator
I have been looking around for a single axis potentiometer self centering but these 2axis are the only ones I can find. At least small. Lots of um but about size of a 50cent piece.
__________________
Always wasting money, as the wife says. To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
|
|
#11
11-26-2016, 05:47 PM
|
|||
|
|||
|
Re: Need a Track control switch for 4200 excavator
I hope someone can chime in cause I need to replace my duals with a couple of these switched and rc4wd cannot come up with them. They keep trying to send me the metal extensions for 70 bucks.
|
|
#12
11-28-2016, 12:28 AM
|
|||
|
|||
|
Re: Need a Track control switch for 4200 excavator
Quote:
|
|
| Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|
Hybrid Mode
