![]() |
|
Construction Equipment If it digs, pushes, hauls dirt "off road" post it here. |
![]() |
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
![]()
This is my attempt ( and I use that loosely) at converting a bruder 574 to rc.
I will upload my pics and my progress, any comments and tips will be greatly appreciated. This is my first go at anything rc. |
#2
|
|||
|
|||
![]()
Sweet! I'm actually doing a loader build as well, this should help me!! This is perfect! Thank you! Are you going to post where you get the servos and what they are cause I'm new and that would be cool. I also am new to the whole transmitter and receiver thing and also new concerning what motors to by/what's the best one for the lowest money lol
|
#3
|
|||
|
|||
![]()
Hi, I have done quite a lot of research on different ways to do this conversion.
I have already purchased things like Drive motors for the wheels, Esc's both brushed and brushless, ( I didnt even know what the difference was ). I have also purchased some aluminium in different sizes. I got the tyres that i will be using and i also have the radio, which is a Flysky i6. I Last edited by jdwtrans; 05-10-2016 at 01:57 PM. |
#4
|
|||
|
|||
![]() |
#5
|
|||
|
|||
![]()
RCP57 did a nice Bruder build and so did KAF343. They both turned out really well. I am in the midst of my conversion as well... I am just waiting for parts to show up so I can keep building. Its a long wait when parts are coming from over seas.
Keep the pictures coming. |
#6
|
|||
|
|||
![]()
Yep, right there with ya man. I don't know where to start or what controller to buy, they all seem so expensive. I was thinking of just buying the hobby engine loader with the spectrum remote and replacing some of the motors with ones that have better range of motion (if that's doable)
|
#7
|
|||
|
|||
![]()
Hi all, 1 thing i have noticed on here is the amount of attention to detail on some of your builds. i am stunned and i think that is gonna be a very hard act to follow.
Just like my school reports- could try harder ! i guess some things never change. |
#8
|
|||
|
|||
![]() Quote:
|
#9
|
|||
|
|||
![]() |
#10
|
|||
|
|||
![]() |
#11
|
|||
|
|||
![]()
Nice work bud. Wat rpm motors u hav ?
|
#12
|
|||
|
|||
![]()
Thanks, I bought 2 sets the first are 20rpm and I'm hoping that will give a scale speed. And I also got some 78's if I want to get lairy.
|
#13
|
|||
|
|||
![]()
Well i have been very busy today:
[IMG] ![]() Thought i would try my hand at aluminium welding not the best but its strong enough. I also wired up and tested my pump. [IMG] ![]() Front half is nearly complete, i made scale pins for the arms and i even managed to put some LED's in some lights that i got for the front. [IMG] ![]() |
#14
|
||||
|
||||
![]()
Very nice cnxersion! Is that aluminum brazed together?
|
#15
|
|||
|
|||
![]()
Yes, I just used butane gas and some aluminium brazing rods, it's my first attempt at it and I'm surprised how well it flows, it does take quite a bit of heat though.
|
#16
|
|||
|
|||
![]() |
#17
|
|||
|
|||
![]()
I also picked up this little thang. Its a light/sound module where you can do channel proportioning, it come with software and everything is stored on a micro sd card. I have installed the software and i must say its a brilliant little module. i can also control the pump through this.
[IMG] ![]() BTW it's made by Beirer and it's a USM-2 |
#18
|
|||
|
|||
![]() |
#19
|
|||
|
|||
![]() |
#20
|
|||
|
|||
![]()
That is coming along great.
Looks like you've got the doctor and his telephone booth beaten by a long shot with your very own shed. LoL If you have a magic screw driver in there as well I think your Bruder conversion will be exemplary. Keep up the good work, and post as much pics as you can. |
![]() |
Tags |
bruder, radlader 574 |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|