Michigan Gravel Train

[RCP57]

I started on this one late last year. I took a break from it for a while but have been back at it this week. A bit more work to do on it but it's coming along.

https://www.youtube.com/watch?v=dPf4lpkcPTI

[ScottLay]

That is one sweet rig!!!!!

[Lil Giants]

I see what you mean about the suspension, perhaps with regular use it will improve. Gonna take a heavy trk to pull the combo in the dirt! A chunk of plate steel in the trl frame right over 5th wheel?

[neil burritt]

that truck looks totally awesome

[RCP57]

Originally Posted by Lil Giants

I see what you mean about the suspension, perhaps with regular use it will improve. Gonna take a heavy trk to pull the combo in the dirt! A chunk of plate steel in the trl frame right over 5th wheel?

I think it might Joe. The supplied springs are very stiff so they might soften. On the first trailer I built using them, I changed out the springs in the rear axle so that it sagged a bit. On the longer trailers it isn't as noticeable so the last couple I have left as is. These ones are relatively short so I will "address" the issue with some spacers. The truck is going to need some grunt and traction unless it's run on the flat. Not a bad idea to add some tongue weight.

Originally Posted by neil burritt

that truck looks totally awesome

Thanks, it's not too bad.

I added a push bar to the rear trailer and a few other details yesterday. Need to finish the tarps and get them ready for coating.




Reg

[Mustang46555]

Awesome looking rig!!!

[Jakyat]

Nice job Reg. You are one talented guy. If I had the capabilities and tools that you have for fabricating aluminum, I would never make it to work.

[RCP57]

Originally Posted by Mustang46555

Awesome looking rig!!!

Thank you!

Originally Posted by Jakyat

Nice job Reg. You are one talented guy. If I had the capabilities and tools that you have for fabricating aluminum, I would never make it to work.

Haha, thanks. I went so far as to "make it my work". Not sure if that was the best decision but it is fun to see the look on peoples faces when I tell them I make toys for adults....

https://www.youtube.com/watch?v=veVS26GyfD8

[Northern Farmer]

Wow! Boy did you knock this one out of the park Great job Reg whole setup looks killer

[jack van]

so the big question on my mind how much for the full set ?

[RCP57]

Originally Posted by Northern Farmer

Wow! Boy did you knock this one out of the park Great job Reg whole setup looks killer

Thanks Brandon.

Originally Posted by jack van

so the big question on my mind how much for the full set ?

$3500USD

[pontiacmann]

Looks great, can they tip? for that Price?

[RCP57]

Originally Posted by pontiacmann

Looks great, can they tip? for that Price?

Yeah of course. Tarps work as well.

[pontiacmann]

and lights to??

[RCP57]

Originally Posted by pontiacmann

and lights to??

I don't do lights. I just drill holes for them where I'm asked.

[Lil Giants]

Reg, did you ever get your box of parts that you were waiting for on this build? If not, maybe this is what happened to them...

https://www.theweathernetwork.com/ca.../5296011243001

[RCP57]

I had heard about that Joe but no that's not the issue here. The parts still haven't shown up but they were shipped using Hong Kong post air mail. rcMart is looking into it apparently but they said it can take up to two months for the postal service to determine that they were not delivered. It's been about a month since they started "looking into it" and I've heard nothing from them for three weeks. The parts shipped November 16 so I am tired of waiting to get my money back. I have never used the buyer protection on PayPal but I think it is time to give it a try. I'm not made of money here and losing over $100USD in parts is not helping me any.

[Lil Giants]

Is the time limit still 45 days to claim refund?

[RCP57]

Originally Posted by Lil Giants

Is the time limit still 45 days to claim refund?

No I think it's 6 months which is ridiculously long IMO.

[RCP57]

I got these parts back from coating on Tuesday morning but I went away for a day and a half right after so I didn't get started on them until yesterday. It is a lot of work just to reassemble all of these parts after coating. Every hole has to be carefully chased with a tap before anything else can happen and that takes some time. Anyway, however many hours later I have this!












Reg