2 IH 433 payscrapers (ps433-2 moves)

[fhhhstix]

Looks good Steve your getting there slowly but your getting there.

Travis

[Snochaser]

Nice Steve, you'll be able to run shale through that with the weight and strength.

[Izzy]

I like Steve - plenty of power and not too fast so it makes nice clean cuts

What's left to do?

[ihbuilder]

Originally Posted by SmallHaul

Nice power Steve!

That machine is sooo heavy it should shave earth easily.

Originally Posted by fhhhstix

Looks good Steve your getting there slowly but your getting there.

Travis

Originally Posted by Snochaser

Nice Steve, you'll be able to run shale through that with the weight and strength.

Originally Posted by Izzy

I like Steve - plenty of power and not too fast so it makes nice clean cuts

What's left to do?

thanks guys yea she'll load well can push me across the floor Chris ,I got a lot more to do but it went back on the shelf again like all my stuff I got to much to do and deal with right now and get everyone's stuff made . the list keeps getting longer

IHSteve

[rc_farmer]

Steve, you are doing a great job, can't wait to see you cut some mud!

[td9clyde]

Steve ........hows things going? haven't seen any update pics lately hows your 40 comming along?

[ihbuilder]

Originally Posted by rc_farmer

Steve, you are doing a great job, can't wait to see you cut some mud!

yea I can't either

Originally Posted by td9clyde

Steve ........hows things going? haven't seen any update pics lately hows your 40 comming along?

back on the shelf for now Henry , same with the 40 . I kinda got this new toy and got to get it making some dough and right now It's got me a little trying to figure why it will not come off em stop error 04 it seems 2 servo amps where replaced within months of each other but 1 does not appear to have been replaced . Also trying to figure out how a running machine before I bought it ( saw a vid of it running maybe this 1 or the 1 they still use ) and not when I set it up 1 referb amp $1000.00 for glentek and $350.00 for a rebuilt SD1525-16 which I think is OEM not only that , I got orders and trying to get some of these trls wrapped up and out of the shop till I decide to light them up .

Steve

[ihbuilder]

well lucky for me there's nothing wrong with the mill now I just need phase conversion for the spindle turns out I forgot a wire when separating the control from the power switch for the whole machine .

IHSteve

[ihbuilder]

I'm wrapping up my highway truck building and coming back to my construction equip. . after sometime on pondering this build ,I decided to change the motors ( to slow ) When I got the motors , I over looked the output speed of the motor being reduced by the differentials . since I'm taking the motor I was going to use in the TD40B I need replacements these are the right size to go side by side and got plenty of room to play with gears ratios and multi-speed trans. Also I'm going to bite the bullet and buy the hydros .

Steve

[ihbuilder]

I put this back on the bench after I saw Steve do a motor swap on his tunarocker I had 2 motor siting around with double the speed as the original , so did a motor swap and Stevie is a happy camper I was going to try to get it going for cabin fever and supprise everyone but As always not enough time to do both pan and mack we'll see how it goes though

[td9clyde]

i seen those at tri state tractor show lol nice try Steve can't pull a fast one that easy nice models though

[ihbuilder]

now I know what was under all that dust in the corner

I started on remaking the gooseneck . The block in the vise is 5"x3.5" x 24" still need to finish the top and flip and cut the underside out .













till next time

[RCP57]

I was getting worried about you! I thought you were too busy making money and forgot that you have to build yourself some stuff to keep it fun. All joking aside, I'm happy to see you milling some parts again for one of your many projects! It's not the same around here when we don't have your "updates" to look at.

[Snochaser]

Keep the chips flyin'. Pokie!! Looks good.

[ihbuilder]

Originally Posted by RCP57

I was getting worried about you! I thought you were too busy making money and forgot that you have to build yourself some stuff to keep it fun. All joking aside, I'm happy to see you milling some parts again for one of your many projects! It's not the same around here when we don't have your "updates" to look at.

making $$ problem is I enjoy makin stuff that I get to many ideas goin at once . I know I can make this werk just need to keep at er .

Originally Posted by Snochaser

Keep the chips flyin'. Pokie!! Looks good.

thanks ben waitin for more brass to come in

[ihbuilder]

More setup pics, finished part - the welding , and comparison pics

first is setup to face the outside . I don't have a sine plate so a lil improvising the facing was done manually no need to waist time programing that I did a lot of setups do to what I had in long (lack of ) length end mills





cut out last op


what I couldn't do with the 1st neck


1:25


comparisons




cpt jack running the 1:25



till next time

[ihbuilder]

I did make the new wheels for it over a year ago (dust )just never posted them . The caps are programed just need to put a plate in the vise and cut .

[Stefan]

Great work!

[dabears]

Glad to see your back at this one!!! Cant wait to see more shavings flyin

[Espeefan]

I love watching parts being machined. The new neck looks great, and I like those models too. First Gear replicas?